49 C.F.R. Subpart G—Maintenance
Title 49 - Transportation
Source: Amdt. 193–2, 45 FR 70407, Oct. 23, 1980, unless otherwise noted.
This subpart prescribes requirements for maintaining components at LNG plants. (a) Each component in service, including its support system, must be maintained in a condition that is compatible with its operational or safety purpose by repair, replacement, or other means. (b) An operator may not place, return, or continue in service any component which is not maintained in accordance with this subpart. (c) Each component taken out of service must be identified in the records kept under §193.2639. (d) If a safety device is taken out of service for maintenance, the component being served by the device must be taken out of service unless the same safety function is provided by an alternate means. (e) If the inadvertent operation of a component taken out of service could cause a hazardous condition, that component must have a tag attached to the controls bearing the words “do not operate” or words of comparable meaning. (a) Each operator shall determine and perform, consistent with generally accepted engineering practice, the periodic inspections or tests needed to meet the applicable requirements of this subpart and to verify that components meet the maintenance standards prescribed by this subpart. (b) Each operator shall follow one or more manuals of written procedures for the maintenance of each component, including any required corrosion control. The procedures must include: (1) The details of the inspections or tests determined under paragraph (a) of this section and their frequency of performance; and (2) A description of other actions necessary to maintain the LNG plant according to the requirements of this subpart. (c) Each operator shall include in the manual required by paragraph (b) of this section instructions enabling personnel who perform operation and maintenance activities to recognize conditions that potentially may be safety-related conditions that are subject to the reporting requirements of §191.23 of this subchapter. [Amdt. 193–2, 45 FR 70407, Oct. 23, 1980, as amended by Amdt. 193–5, 53 FR 24950, July 1, 1988; 53 FR 26560, July 13, 1988; Amdt. 193–18, 69 FR 11337, Mar. 10, 2004] (a) The presence of foreign material, contaminants, or ice shall be avoided or controlled to maintain the operational safety of each component. (b) LNG plant grounds must be free from rubbish, debris, and other material which present a fire hazard. Grass areas on the LNG plant grounds must be maintained in a manner that does not present a fire hazard. Each support system or foundation of each component must be inspected for any detrimental change that could impair support. (a) Maintenance activities on fire control equipment must be scheduled so that a minimum of equipment is taken out of service at any one time and is returned to service in a reasonable period of time. (b) Access routes for movement of fire control equipment within each LNG plant must be maintained to reasonably provide for use in all weather conditions. Each auxiliary power source must be tested monthly to check its operational capability and tested annually for capacity. The capacity test must take into account the power needed to start up and simultaneously operate equipment that would have to be served by that power source in an emergency. (a) Before personnel begin maintenance activities on components handling flammable fluids which are isolated for maintenance, the component must be purged in accordance with a procedure which meets the requirements of AGA “Purging Principles and Practices,” unless the maintenance procedures under §193.2605 provide that the activity can be safely performed without purging. (b) If the component or maintenance activity provides an ignition source, a technique in addition to isolation valves (such as removing spool pieces or valves and blank flanging the piping, or double block and bleed valving) must be used to ensure that the work area is free of flammable fluids. (a) Repair work on components must be performed and tested in a manner which: (1) As far as practicable, complies with the applicable requirements of Subpart D of this part; and (2) Assures the integrity and operational safety of the component being repaired. (b) For repairs made while a component is operating, each operator shall include in the maintenance procedures under §193.2605 appropriate precautions to maintain the safety of personnel and property during repair activities. (a) Each control system must be properly adjusted to operate within design limits. (b) If a control system is out of service for 30 days or more, it must be inspected and tested for operational capability before returning it to service. (c) Control systems in service, but not normally in operation, such as relief valves and automatic shutdown devices, and control systems for internal shutoff valves for bottom penetration tanks must be inspected and tested once each calender year, not exceeding 15 months, with the following exceptions: (1) Control systems used seasonally, such as for liquefaction or vaporization, must be inspected and tested before use each season. (2) Control systems that are intended for fire protection must be inspected and tested at regular intervals not to exceed 6 months. (d) Control systems that are normally in operation, such as required by a base load system, must be inspected and tested once each calendar year but with intervals not exceeding 15 months. (e) Relief valves must be inspected and tested for verification of the valve seat lifting pressure and reseating. [Amdt. 193–2, 45 FR 70407, Oct. 23, 1980, as amended by Amdt. 193–17, 65 FR 10960, Mar. 1, 2000] Hoses used in LNG or flammable refrigerant transfer systems must be: (a) Tested once each calendar year, but with intervals not exceeding 15 months, to the maximum pump pressure or relief valve setting; and (b) Visually inspected for damage or defects before each use. Each LNG storage tank must be inspected or tested to verify that each of the following conditions does not impair the structural integrity or safety of the tank: (a) Foundation and tank movement during normal operation and after a major meteorological or geophysical disturbance. (b) Inner tank leakage. (c) Effectiveness of insulation. (d) Frost heave. [Amdt. 193–2, 45 FR 70407, Oct. 23, 1980, as amended at 47 FR 32720, July 29, 1982] (a) Each operator shall determine which metallic components could, unless corrosion is controlled, have their integrity or reliability adversely affected by external, internal, or atmospheric corrosion during their intended service life. (b) Components whose integrity or reliability could be adversely affected by corrosion must be either— (1) Protected from corrosion in accordance with §§193.2627 through 193.2635, as applicable; or (2) Inspected and replaced under a program of scheduled maintenance in accordance with procedures established under §193.2605. Each exposed component that is subject to atmospheric corrosive attack must be protected from atmospheric corrosion by— (a) Material that has been designed and selected to resist the corrosive atmosphere involved; or (b) Suitable coating or jacketing. (a) Each buried or submerged component that is subject to external corrosive attack must be protected from external corrosion by— (1) Material that has been designed and selected to resist the corrosive environment involved; or (2) The following means: (i) An external protective coating designed and installed to prevent corrosion attack and to meet the requirements of §192.461 of this chapter; and (ii) A cathodic protection system designed to protect components in their entirety in accordance with the requirements of §192.463 of this chapter and placed in operation before October 23, 1981, or within 1 year after the component is constructed or installed, whichever is later. (b) Where cathodic protection is applied, components that are electrically interconnected must be protected as a unit. [Amdt. 193–2, 45 FR 70407, Oct. 23, 1980, as amended at 47 FR 32720, July 29, 1982] Each component that is subject to internal corrosive attack must be protected from internal corrosion by— (a) Material that has been designed and selected to resist the corrosive fluid involved; or (b) Suitable coating, inhibitor, or other means. (a) Each component that is subject to electrical current interference must be protected by a continuing program to minimize the detrimental effects of currents. (b) Each cathodic protection system must be designed and installed so as to minimize any adverse effects it might cause to adjacent metal components. (c) Each impressed current power source must be installed and maintained to prevent adverse interference with communications and control systems. Corrosion protection provided as required by this subpart must be periodically monitored to give early recognition of ineffective corrosion protection, including the following, as applicable: (a) Each buried or submerged component under cathodic protection must be tested at least once each calendar year, but with intervals not exceeding 15 months, to determine whether the cathodic protection meets the requirements of §192.463 of this chapter. (b) Each cathodic protection rectifier or other impressed current power source must be inspected at least 6 times each calendar year, but with intervals not exceeding 2 (c) Each reverse current switch, each diode, and each interference bond whose failure would jeopardize component protection must be electrically checked for proper performance at least 6 times each calendar year, but with intervals not exceeding 2 (d) Each component that is protected from atmospheric corrosion must be inspected at intervals not exceeding 3 years. (e) If a component is protected from internal corrosion, monitoring devices designed to detect internal corrosion, such as coupons or probes, must be located where corrosion is most likely to occur. However, monitoring is not required for corrosion resistant materials if the operator can demonstrate that the component will not be adversely affected by internal corrosion during its service life. Internal corrosion control monitoring devices must be checked at least two times each calendar year, but with intervals not exceeding 7 Prompt corrective or remedial action must be taken whenever an operator learns by inspection or otherwise that atmospheric, external, or internal corrosion is not controlled as required by this subpart. (a) Each operator shall keep a record at each LNG plant of the date and type of each maintenance activity performed on each component to meet the requirements of this part. For each LNG facility that is designed and constructed after March 31, 2000 the operator shall also maintain related periodic inspection and testing records that NFPA 59A (incorporated by reference, see §193.2013) requires. Maintenance records, whether required by this part or NFPA 59A, must be kept for a period of not less than five years. (b) Each operator shall maintain records or maps to show the location of cathodically protected components, neighboring structures bonded to the cathodic protection system, and corrosion protection equipment. (c) Each of the following records must be retained for as long as the LNG facility remains in service: (1) Each record or map required by paragraph (b) of this section. (2) Records of each test, survey, or inspection required by this subpart in sufficient detail to demonstrate the adequacy of corrosion control measures. [Amdt. 193–2, 45 FR 70407, Oct. 23, 1980, as amended by Amdt. 193–17, 65 FR 10960, Mar. 1, 2000; Amdt. 193–18, 69 FR 11337, Mar. 10, 2004]
Title 49: Transportation
PART 193—LIQUEFIED NATURAL GAS FACILITIES: FEDERAL SAFETY STANDARDS
Subpart G—Maintenance
§ 193.2601 Scope.
§ 193.2603 General.
§ 193.2605 Maintenance procedures.
§ 193.2607 Foreign material.
§ 193.2609 Support systems.
§ 193.2611 Fire protection.
§ 193.2613 Auxiliary power sources.
§ 193.2615 Isolating and purging.
§ 193.2617 Repairs.
§ 193.2619 Control systems.
§ 193.2621 Testing transfer hoses.
§ 193.2623 Inspecting LNG storage tanks.
§ 193.2625 Corrosion protection.
§ 193.2627 Atmospheric corrosion control.
§ 193.2629 External corrosion control: buried or submerged components.
§ 193.2631 Internal corrosion control.
§ 193.2633 Interference currents.
§ 193.2635 Monitoring corrosion control.
§ 193.2637 Remedial measures.
§ 193.2639 Maintenance records.
