49 C.F.R. PART 585—PHASE–IN REPORTING REQUIREMENTS
Title 49 - Transportation
Authority: 49 U.S.C. 322, 30111, 30115, 30117, and 30166; delegation of authority at 49 CFR 1.50.
Source: 69 FR 70916, Dec. 8, 2004, unless otherwise noted.
(a) All terms defined in 49 U.S.C. 30102 are used in accordance with their statutory meaning. (b) The terms bus, gross vehicle weight rating or GVWR, motor vehicle, multipurpose passenger vehicle, passenger car, and truck are used as defined in §571.3 of this chapter. (c) Production year means the 12-month period between September 1 of one year and August 31 of the following year, inclusive, unless otherwise specified. Each report submitted to NHTSA under this part shall: (a) Identify the manufacturer; (b) State the full name, title, and address of the official responsible for preparing the report; (c) Identify the production year being reported on; (d) Contain a statement regarding whether or not the manufacturer complied with the requirements of the Federal motor vehicle safety standard addressed by the report, for the period covered by the report, and the basis for that statement; (e) Be written in the English language; and (f) Be submitted to: Administrator, National Highway Traffic Safety Administration, 400 Seventh Street, SW., Washington, DC 20590. Each manufacturer whose reporting of information is affected by one or more of the express written contracts permitted by a Federal Motor Vehicle Safety Standard subject to the reporting requirements of this part shall: (a) Report the existence of each contract, including the names of all parties to the contract and explain how the contract affects the report being submitted. (b) Report the number of vehicles covered by each contract in each production year. A petition for extension of the time to submit a report required under this part shall be received not later than 15 days before the report is due. The petition shall be submitted to: Administrator, National Highway Traffic Safety Administration, 400 Seventh Street, SW., Washington, DC 20590. The filing of a petition does not automatically extend the time for filing a report. A petition will be granted only if the petitioner shows good cause for the extension, and if the extension is consistent with the public interest. This subpart establishes requirements for manufacturers of passenger cars and trucks, buses, and multipurpose passenger vehicles with a GVWR of 3,855 kg or less and an unloaded vehicle weight of 2,495 kg or less to submit reports, and maintain records related to the reports, concerning the number and identification of such vehicles that are certified as complying with the advanced air bag requirements of Standard No. 208, Occupant crash protection (49 CFR 571.208). The purpose of these reporting requirements is to aid the National Highway Traffic Safety Administration in determining whether a manufacturer has complied with the advanced air bag requirements of Standard No. 208 during the phase-ins of those requirements. This subpart applies to manufacturers of passenger cars and trucks, buses, and multipurpose passenger vehicles with a GVWR of 3,855 kg or less and an unloaded vehicle weight of 2,495 kg or less. However, this subpart does not apply to any manufacturers whose production consists exclusively of walk-in vans, vehicles designed to be sold exclusively to the U.S. Postal Service, vehicles manufactured in two or more stages, and vehicles that are altered after previously having been certified in accordance with part 567 of this chapter. In addition, this subpart does not apply to manufacturers whose production of motor vehicles for the United States market is less than 5,000 vehicles in a production year. For the purposes of this subpart, (a) Phase one of the advanced air bag requirements of Standard No. 208 refers to the requirements set forth in S14.1, S14.2, S14.5.1(a), S14.5.2, S15.1, S15.2, S17, S19, S21, S23, and S25 of Federal Motor Vehicle Safety Standard No. 208, 49 CFR 571.208. (b) Phase two of the advanced air bag reporting requirements of Standard No. 208 refers to the requirements set forth in S14.3, S14.4, S14.5.1(b), S14.5.2, S15.1, S15.2, S17, S19, S21, S23, and S25 of Federal Motor Vehicle Safety Standard No. 208, 49 CFR 571.208. (c) Vehicles means passenger cars and trucks, buses, and multipurpose passenger vehicles with a GVWR of 3,855 kg or less and an unloaded vehicle weight of 2,495 kg or less manufactured for sale in the United States whose production of motor vehicles for sale in the United States is equal to or greater than 5,000 vehicles in a production year, and does not mean walk-in vans, vehicles designed to be sold exclusively to the U.S. Postal Service, vehicles manufactured in two or more stages, and vehicles that are altered after previously having been certified in accordance with part 567 of this chapter. (a) Advanced credit phase-in reporting requirements. (1) Within 60 days after the end of production years ending August 31, 2000, August 31, 2001, August 31, 2002, and August 31, 2003, each manufacturer choosing to certify vehicles manufactured during any of those production years as complying with phase one of the advanced air bag requirements of Standard No. 208 shall submit a report to the National Highway Traffic Safety Administration providing the information specified in paragraph (c) of this section and in §585.2 of this part. (2) Within 60 days after the end of the production year ending August 31, 2007, each manufacturer choosing to certify vehicles manufactured during that production year as complying with phase two of the advanced air bag requirements of Standard No. 208 shall submit a report to the National Highway Traffic Safety Administration providing the information specified in paragraph (c) of this section and in §585.2 of this part. (b) Phase-in reporting requirements. (1) Within 60 days after the end of the production years ending August 31, 2004, August 31, 2005, and August 31, 2006, each manufacturer shall submit a report to the National Highway Traffic Safety Administration regarding its compliance with phase one of the advanced air bag requirements of Standard No. 208 for its vehicles produced in that production year. The report shall provide the information specified in paragraph (d) of this section and in §585.2 of this part. Each report shall also specify the number of advance credit vehicles, if any, which are being applied to the production year being reported on. (2) Within 60 days after the end of production years ending August 31, 2008, August 31, 2009, and August 31, 2010, each manufacturer shall submit a report to the National Highway Traffic Safety Administration regarding its compliance with phase two of the advanced air bag requirements of Standard No. 208 for its vehicles produced in that production year. The report shall provide the information specified in paragraph (d) of this section and in §585.2 of this part. Each report shall also specify the number of advance credit vehicles, if any, which are being applied to the production year being reported on. (c) Advanced credit phase-in report content. (1) With respect to the reports identified in section 585.15(a)(1), each manufacturer shall report for the production year for which the report is filed the number of vehicles, by make and model year, that meet the applicable advanced air bag requirements of Standard No. 208, and to which advanced air bag requirements the vehicles are certified. (2) With respect to the report identified in section 585.15(a)(2), each manufacturer shall report the number of vehicles, by make and model year, that meet the applicable advanced air bag requirements of Standard No. 208, and to which the advanced air bag requirements the vehicles are certified. (d) Phase-in report content. (1) Basis for phase-in production requirements. For production years ending August 31, 2003, August 31, 2004, August 31, 2005, August 31, 2007, August 31, 2008, and August 31, 2009, each manufacturer shall provide the number of vehicles manufactured in the current production year, or, at the manufacturer's option, for the current production year and each of the prior two production years if the manufacturer has manufactured vehicles during both of the two production years prior to the year for which the report is being submitted. (2) Production of complying vehicles. Each manufacturer shall report for the production year for which the report is filed the number of vehicles, by make and model year, that meet the applicable advanced air bag requirements of Standard No. 208, and to which advanced air bag requirements the vehicles are certified. Each manufacturer shall maintain records of the Vehicle Identification Number of each vehicle for which information is reported under §585.15(c)(1) and (d)(2) until December 31, 2011. This subpart establishes requirements for manufacturers of passenger cars and for trucks, buses, and multipurpose passenger vehicles with a GVWR of 4,536 kg (10,000 lb) or less to submit reports, and maintain records related to the reports, concerning the number and identification of such vehicles that are certified as complying with the Type 2 seat belt requirements for rear seating positions of Standard No. 208, Occupant crash protection (49 CFR 571.208). The purpose of these reporting requirements is to assist the National Highway Traffic Safety Administration in determining whether a manufacturer has complied with the Type 2 seat belt requirements for rear seating positions of Standard No. 208. This subpart applies to manufacturers of passenger cars and trucks, buses, and multipurpose passenger vehicles with a GVWR of 4,536 kg or less. However, this subpart does not apply to any manufacturers whose production consists exclusively of walk-in vans, vehicles designed to be sold exclusively to the U.S. Postal Service, vehicles manufactured in two or more stages, and vehicles that are altered after previously having been certified in accordance with part 567 of this chapter. In addition, this subpart does not apply to manufacturers whose worldwide production of motor vehicles is less than 5,000 vehicles in a production year. (a) Advanced credit phase-in reporting requirements. Within 60 days after the end of the production year ending August 31, 2005, each manufacturer choosing to certify vehicles manufactured during that production year as complying with the Type 2 seat belt for each rear designated seating position requirements of Standard No. 208 shall submit a report to the National Highway Traffic Safety Administration providing the information specified in paragraph (c) of this section and in §585.2 of this part. (b) Phase-in reporting requirements. Within 60 days after the end of the production years ending August 31, 2006, and August 31, 2007, each manufacturer shall submit a report to the National Highway Traffic Safety Administration regarding its compliance with the Type 2 seat belt for each rear designated seating position requirements of Standard No. 208 for its vehicles produced in that production year. The report shall provide the information specified in paragraph (d) of this section and in §585.2 of this part. Each report shall also specify the number of advance credit vehicles, if any, which are being applied to the production year being reported on. (c) Advanced credit phase-in report content. With respect to the reports identified in section 585.24(a), each manufacturer shall report for the production year for which the report is filed the number of vehicles, by make and model year, that meet the applicable Type 2 seat belt for each rear designated seating position requirements of Standard No. 208. (d) Phase-in report content. (1) Basis for phase-in production requirements. For production years ending August 31, 2006, and August 31, 2007, each manufacturer shall provide the number of vehicles manufactured in the current production year, or, at the manufacturer's option, for the current production year and each of the prior two production years if the manufacturer has manufactured vehicles during each production year prior to the year for which the report is being submitted. (2) Production of complying vehicles. Each manufacturer shall report for the production year for which the report is filed the number of vehicles, by make and model year, that meet the applicable Type 2 seat belt for each rear designated seating position requirements of Standard No. 208. Each manufacturer shall maintain records of the Vehicle Identification Number of each vehicle for which information is reported under §585.24(c) and (d)(2) until December 31, 2008. This subpart established requirements for manufacturers of passenger cars and of trucks and multipurpose passenger vehicles with a GVWR of 3,855 kg or less, and of buses with a GVWR of 4,536 kg or less, to submit a report, and maintain records related to the report, concerning the number of such vehicles that meet the requirements of Standard No. 225, Child restraint anchorage systems (49 CFR 571.225). The purpose of these reporting requirements is to assist the National Highway Traffic Safety Administration in determining whether a manufacturer has complied with Standard No. 225. This subpart applies to manufacturers of passenger cars, and of trucks and multipurpose passenger vehicles with a GVWR of 3,855 kg or less, and of buses with a GVWR of 4,536 kg or less. However, this subpart does not apply to vehicles excluded by S5 of Standard No. 225 from the requirements of the standard. At any time during the production years ending August 31, 2000, August 31, 2001, August 31, 2002, and August 31, 2005 each manufacturer shall, upon request from the Office of Vehicle Safety Compliance, provide information identifying the vehicles (by make, model and vehicle identification number) that have been certified as complying with Standard No. 225. The manufacturer's designation of a vehicle as a certified vehicle is irrevocable. (a) General reporting requirements. Within 60 days after the end of the production years ending August 31, 2000, August 31, 2001, and August 31, 2002, each manufacturer shall submit a report to the National Highway Traffic Safety Administration concerning its compliance with the child restraint anchorage system requirements of Standard No. 225 for its passenger cars, trucks, buses, and multipurpose passenger vehicles produced in that year. The report shall provide the information specified in paragraph (b) of this section and in §585.2 of this part. (b) Report content—(1) Basis for phase-in production goals. Each manufacturer shall provide the number of passenger cars and trucks and multipurpose passenger vehicles with a GVWR of 3,855 kg or less, and buses with a GVWR of 4,536 kg or less manufactured for sale in the United States for each of the three previous production years, or, at the manufacturer's option, for the current production year. A new manufacturer that has not previously manufactured these vehicles for sale in the United States shall report the number of such vehicles manufactured during the current production year. (2) Production. (i) Each manufacturer shall report for the production year for which the report is filed, except for the production year ending August 31, 2005: the number of passenger cars and trucks and multipurpose passenger vehicles with a GVWR of 3,855 kg or less, and buses with a GVWR of 4,536 kg or less, that meet Standard No. 225. (ii) Each manufacturer shall report for the production year ending August 31, 2005: the number of passenger cars and trucks and multipurpose passenger vehicles with a GVWR of 3,855 kg or less, and buses with a GWVR of 4,536 kg or less, that meet S6.3.1 and S9.4 of Standard No. 225. Each manufacturer shall maintain records of the Vehicle Identification Number for each vehicle for which information is reported under §585.35(b)(2)(i) until December 31, 2004. Each manufacturer shall maintain records of the Vehicle Identification Number for each vehicle for which information is reported under §585.35(b)(2)(ii) until December 31, 2007. This subpart establishes requirements for manufacturers of passenger cars, multipurpose passenger vehicles, trucks, and buses with a GVWR of 4,536 kg (10,000 lb) or less to respond to NHTSA inquiries, to submit reports, and to maintain records related to the reports, concerning the number of such vehicles that meet the upgraded requirements of Standard No. 301, Fuel systems integrity (49 CFR 571.301). The purpose of these requirements is to assist the National Highway Traffic Safety Administration in determining whether a manufacturer has complied with the upgraded requirements of Standard No. 301. This subpart applies to manufacturers of passenger cars, multipurpose vehicles, trucks and buses with a GVWR of 4,536 kg or less. During the production years ending August 31, 2007, August 31, 2008, and August 31, 2009, each manufacturer shall, upon request from the Office of Vehicle Safety Compliance, provide information identifying the vehicles (by make, model, and vehicle identification number) that have been certified as complying with the requirements of S6.2(b) of Standard No. 301. The manufacturer's designation of a vehicle as a certified vehicle is irrevocable. (a) General reporting requirements. Within 60 days after the end of the production years ending August 31, 2007, August 31, 2008 and August 31, 2009, each manufacturer shall submit a report to the National Highway Traffic Safety Administration concerning its compliance with S6.2(b) of Standard No. 301 for its passenger cars, multipurpose passenger vehicles, trucks, and buses with a GVWR of less than 4,536 kg produced in that year. Each report shall provide the information specified in paragraph (b) of this section and in section 585.2 of this part. (b) Report content. (1) Basis for statement of compliance. Each manufacturer shall provide the number of passenger cars, multipurpose passenger vehicles, trucks, and buses with a GVWR of 4,536 kg or less manufactured for sale in the United States for each of the three previous production years, or, at the manufacturer's option, for the previous production year. A new manufacturer that has not previously manufactured these vehicles for sale in the United States must report the number of such vehicles manufactured during the current production year. (2) Production. Each manufacturer shall report for the production year for which the report is filed the number of passenger cars, multipurpose passenger vehicles, trucks, and buses with a GVWR of 4,536 kg or less that meet S6.2(b) or S6.3(b) of Standard No. 301. Each manufacturer shall maintain records of the Vehicle Identification Number for each vehicle for which information is reported under §585.45(b)(2) until December 31, 2010. This subpart establishes requirements for manufacturers of new pneumatic tires for motor vehicles with a GVWR of 4,536 kg (10,000 lb) or less to respond to NHTSA inquiries, to submit reports, and to maintain records related to the reports, concerning the number of such tires that meet the requirements of Standard No. 139, New pneumatic tires for light vehicles (49 CFR 571.139). The purpose of these requirements is to assist the National Highway Traffic Safety Administration in determining whether a manufacturer has complied with the requirements of Standard No. 139. This subpart applies to manufacturers of tires for motor vehicles with a GVWR of 4,536 kg or less. Each manufacturer shall, upon request from the Office of Vehicle Safety Compliance, provide information identifying the tires (by make, model, brand and tire identification number) that have been certified as complying with the requirements of Standard No. 139. The manufacturer's designation of a tire as a certified tire is irrevocable. (a) General reporting requirements. Within 60 days after the end of the production years ending August 31, 2006 and August 31, 2007, each manufacturer shall submit a report to the National Highway Traffic Safety Administration concerning its compliance with Standard No. 139 for its tires produced in that year for motor vehicles with a GVWR of 4,536 kg or less. Each report shall provide the information specified in paragraph (b) of this section and in section 585.2 of this part. (b) Report content. (1) Basis for statement of compliance. Each manufacturer shall provide the number of tires for motor vehicles with a GVWR of 4,536 kg or less manufactured for sale in the United States for each of the three previous production years, or, at the manufacturer's option, for the production year for which the report is filed. A new manufacturer that has not previously manufactured these tires for sale in the United States shall report the number of such tires manufactured during the current production year. (2) Production. Each manufacturer shall report for the production year for which the report is filed the number of new pneumatic tires for motor vehicles with a GVWR of 4,536 kg or less that meet Standard No. 139. Each manufacturer shall maintain records of the tire identification number for each vehicle for which information is reported under §585.55(b)(2) until December 31, 2008. Source: 70 FR 18190, Apr. 8, 2005, unless otherwise noted.
This subpart establishes requirements for manufacturers of passenger cars, multipurpose passenger vehicles, trucks, and buses with a gross vehicle weight rating of 4,536 kilograms (10,000 pounds) or less, except those vehicles with dual wheels on an axle, to submit a report, and maintain records related to the report, concerning the number of such vehicles that meet the requirements of Standard No. 138, Tire pressure monitoring systems (49 CFR 571.138). The purpose of these reporting requirements is to assist the National Highway Traffic Safety Administration in determining whether a manufacturer has complied with Standard No. 138. This subpart applies to manufacturers of passenger cars, multipurpose passenger vehicles, trucks, and buses with a gross vehicle weight rating of 4,536 kilograms (10,000 pounds) or less, except those vehicles with dual wheels on an axle. However, this subpart does not apply to manufacturers whose production consists exclusively of vehicles manufactured in two or more stages, and vehicles that are altered after previously having been certified in accordance with part 567 of the chapter. In addition, this subpart does not apply to manufacturers whose production of motor vehicles for the United States market is less than 5,000 vehicles in a production year. Production year means the 12-month period between September 1 of one year and August 31 of the following year, inclusive. At any time prior to August 31, 2007, each manufacturer must, upon request from the Office of Vehicle Safety Compliance, provide information identifying the vehicles (by make, model, and vehicle identification number) that have been certified as complying with Standard No. 138. The manufacturer's designation of a vehicle as a certified vehicle is irrevocable. Upon request, the manufacturer also must specify whether it intends to utilize either carry-forward or carry-backward credits, and the vehicles to which those credits relate. (a) General reporting requirements. Within 60 days after the end of the production years ending August 31, 2006 and August 31, 2007, each manufacturer must submit a report to the National Highway Traffic Safety Administration concerning its compliance with Standard No. 138 (49 CFR 571.138) for its passenger cars, multipurpose passenger vehicles, trucks, and buses with a gross vehicle weight rating of less than 4,536 kilograms (10,000 pounds) produced in that year. Each report must— (1) Identify the manufacturer; (2) State the full name, title, and address of the official responsible for preparing the report; (3) Identify the production year being reported on; (4) Contain a statement regarding whether or not the manufacturer complied with the requirements of Standard No. 138 (49 CFR 571.138) for the period covered by the report and the basis for that statement; (5) Provide the information specified in paragraph (b) of this section; (6) Be written in the English language; and (7) Be submitted to: Administrator, National Highway Traffic Safety Administration, 400 Seventh Street, SW., Washington, DC 20590. (b) Report content—(1) Basis for statement of compliance. Each manufacturer must provide the number of passenger cars, multipurpose passenger vehicles, trucks, and buses with a gross vehicle weight rating of 4,536 kilograms (10,000 pounds) or less, except those vehicles with dual wheels on an axle, manufactured for sale in the United States for each reporting period as follows: (i) Period from October 5, 2005 to August 31, 2006. The number shall be either the manufacturer's average annual production of vehicles manufactured on or after September 1, 2002, and before October 5, 2005, or, at the manufacturer's option, it shall be the manufacturer's production on or after October 5, 2005 and before September 1, 2006. A new manufacturer that has not previously manufactured these vehicles for sale in the United States must report the number of such vehicles manufactured during the production period on or after October 5, 2005 and before September 1, 2006. (ii) Period from September 1, 2006 to August 31, 2007. The number shall be either the manufacturer's average annual production of vehicles manufactured on or after September 1, 2003, and before September 1, 2006, or, at the manufacturer's option, it shall be the manufacturer's production on or after September 1, 2006 and before September 1, 2007. A new manufacturer that has not previously manufactured these vehicles for sale in the United States must report the number of such vehicles manufactured during the production period on or after September 1, 2006 and before September 1, 2007. (2) Production. Each manufacturer must report for the production period for which the report is filed: the total number of passenger cars, multipurpose passenger vehicles, trucks, and buses with a gross vehicle weight rating of 4,536 kilograms (10,000 pounds) or less that meet Standard No. 138 (49 CFR 571.138). (3) Statement regarding compliance. Each manufacturer must provide a statement regarding whether or not the manufacturer complied with the TPMS requirements as applicable to the period covered by the report, and the basis for that statement. This statement must include an explanation concerning the use of any carry-forward and/or carry-backward credits. (4) Vehicles produced by more than one manufacturer. Each manufacturer whose reporting of information is affected by one or more of the express written contracts permitted by S7.5.2 of Standard No. 138 (49 CFR 571.138) must: (i) Report the existence of each contract, including the names of all parties to the contract, and explain how the contract affects the report being submitted. (ii) Report the actual number of vehicles covered by each contract. [70 FR 18190, Apr. 8, 2005, as amended at 70 FR 53101, Sept. 7, 2005] Each manufacturer must maintain records of the Vehicle Identification Number for each vehicle for which information is reported under §585.66(b)(2) until December 31, 2009. A manufacturer may petition for extension of time to submit a report under this Part. A petition will be granted only if the petitioner shows good cause for the extension and if the extension is consistent with the public interest. The petition must be received not later than 15 days before expiration of the time stated in §585.66(a). The filing of a petition does not automatically extend the time for filing a report. The petition must be submitted to: Administrator, National Highway Traffic Safety Administration, 400 Seventh Street, SW., Washington, DC 20590.
Title 49: Transportation
PART 585—PHASE–IN REPORTING REQUIREMENTS
Section Contents
§ 585.1 Definitions.
§ 585.2 Phase-in reports.
§ 585.3 Vehicles produced by more than one manufacturer.
§ 585.4 Petitions to extend period to file report.
§ 585.11 Scope.
§ 585.12 Purpose.
§ 585.13 Applicability.
§ 585.14 Definitions.
§ 585.15 Reporting requirements.
§ 585.16 Records.
§ 585.21 Scope.
§ 585.22 Purpose.
§ 585.23 Applicability.
§ 585.24 Reporting requirements.
§ 585.25 Records.
§ 585.31 Scope.
§ 585.32 Purpose.
§ 585.33 Applicability.
§ 585.34 Response to inquiries.
§ 585.35 Reporting requirements.
§ 585.36 Records.
§ 585.41 Scope.
§ 585.42 Purpose.
§ 585.43 Applicability.
§ 585.44 Response to inquiries.
§ 585.45 Reporting requirements.
§ 585.46 Records.
§ 585.51 Scope.
§ 585.52 Purpose.
§ 585.53 Applicability.
§ 585.54 Response to inquiries.
§ 585.55 Reporting requirements.
§ 585.56 Records.
§ 585.61 Scope.
§ 585.62 Purpose.
§ 585.63 Applicability.
§ 585.64 Definitions.
§ 585.65 Response to inquiries.
§ 585.66 Reporting requirements.
§ 585.67 Records.
§ 585.68 Petition to extend period to file report.
Subpart A—General
top
§ 585.1 Definitions.
top
§ 585.2 Phase-in reports.
top
§ 585.3 Vehicles produced by more than one manufacturer.
top
§ 585.4 Petitions to extend period to file report.
top
Subpart B—Advanced Air Bag Phase-in Reporting Requirements
top
§ 585.11 Scope.
top
§ 585.12 Purpose.
top
§ 585.13 Applicability.
top
§ 585.14 Definitions.
top
§ 585.15 Reporting requirements.
top
§ 585.16 Records.
top
Subpart C—Rear Inboard Lap/Shoulder Belt Phase-In Reporting Requirements
top
§ 585.21 Scope.
top
§ 585.22 Purpose.
top
§ 585.23 Applicability.
top
§ 585.24 Reporting requirements.
top
§ 585.25 Records.
top
Subpart D—Child Restraint Anchorage System Phase-In Reporting Requirements
top
§ 585.31 Scope.
top
§ 585.32 Purpose.
top
§ 585.33 Applicability.
top
§ 585.34 Response to inquiries.
top
§ 585.35 Reporting requirements.
top
§ 585.36 Records.
top
Subpart E—Fuel System Integrity Phase-In Reporting Requirements
top
§ 585.41 Scope.
top
§ 585.42 Purpose.
top
§ 585.43 Applicability.
top
§ 585.44 Response to inquiries.
top
§ 585.45 Reporting requirements.
top
§ 585.46 Records.
top
Subpart F—Tires for Motor Vehicles with a GVWR of 10,000 Pounds or Less Phase-In Reporting Requirements
top
§ 585.51 Scope.
top
§ 585.52 Purpose.
top
§ 585.53 Applicability.
top
§ 585.54 Response to inquiries.
top
§ 585.55 Reporting requirements.
top
§ 585.56 Records.
top
Subpart G—Tire Pressure Monitoring System Phase-in Reporting Requirements
top
§ 585.61 Scope.
top
§ 585.62 Purpose.
top
§ 585.63 Applicability.
top
§ 585.64 Definitions.
top
§ 585.65 Response to inquiries.
top
§ 585.66 Reporting requirements.
top
§ 585.67 Records.
top
§ 585.68 Petition to extend period to file report.
top
